Siemens SIMATIC S7-1200 CPU 1215C DC DC DC PLC 6ES7215-1AG40-0XB0

Siemens SIMATIC S7-1200 CPU 1215C DC DC DC PLC 6ES7215-1AG40-0XB0

6ES7215-1AG40-0XB0 identifies the Siemens SIMATIC S7-1200 CPU 1215C compact PLC in the DC/DC/DC configuration. It combines a 24 V DC controller supply, DC digital inputs and transistor digital outputs in one compact unit. The controller includes fourteen digital inputs, ten digital outputs, two analog voltage inputs and two analog current outputs. It belongs to the conventional S7-1200 generation. The complete ordering number is essential when selecting a replacement, since similarly named CPU 1215C products can have different supply arrangements, output technologies and generation-specific expansion hardware.

Built-in Inputs and Outputs

Fourteen onboard digital inputs accept 24 V DC signals with sinking/sourcing input wiring. Ten onboard outputs use sourcing transistor technology for 24 V DC load circuits, rated at 0.5 A per channel. These outputs are not voltage-free relay contacts. Observe the documented load, group-current and temperature limits, and use suitable suppression for inductive loads. Two onboard analog inputs measure 0–10 V DC signals. Two onboard analog current outputs provide 0–20 mA signals for compatible equipment. These are current outputs; applications requiring voltage outputs need suitable additional hardware. Additional module channels must be counted separately from the CPU channels.

Communication and Programming

Two integrated RJ45 Ethernet/PROFINET ports provide the engineering and network connections through one PROFINET interface. The two physical ports do not represent two independent network interfaces. The physical connector and the configured communication service are separate specifications. PROFINET and SIMATIC communication require appropriate network configuration; serial communication requires a compatible optional CB or CM. Engineering uses SIMATIC STEP 7 in TIA Portal, with LAD, FBD and SCL programming. Current Siemens catalog data lists firmware V4.7 with STEP 7 V20 or higher. Check the firmware installed on a particular unit before choosing software. Software licenses, Ethernet cables and optional communication hardware are separate purchases unless explicitly included by the supplier.

Memory and Technology Functions

Current Siemens product information lists 200 KB of integrated program/data work memory. Do not add load memory or removable memory-card capacity to this figure. Earlier documentation can describe a different firmware-era capacity; verify an existing controller before planning a memory-sensitive replacement. Up to six high-speed counter functions can be configured, subject to input assignment and counting mode. Maximum documented counting frequency is 100 kHz; quadrature operation and individual terminals can have lower limits. Up to four pulse-output functions are available, with designated onboard outputs supporting 100 kHz. Pulse/direction motion requires compatible external drives and correct technology-object configuration. Pulse generators, physical output terminals and independently supported motion axes are different quantities.

Expansion Capability

CPU 1215C supports up to eight local signal modules, up to three communication modules and one shared position for an SB, CB or BB. These limits remain subject to the CPU power budget and compatible hardware. Using eight SM 1223 modules with 16 DI and 16 DO each gives 142 digital inputs and 138 digital outputs including the CPU. Adding a four-input SB 1221 gives a local maximum of 146 digital inputs. Alternatively, a four-output SB 1222 gives a local maximum of 142 digital outputs. These are separate maximum configurations and cannot be achieved simultaneously because the boards occupy the same position. A two-input/two-output SB 1223 instead permits 144 DI and 140 DO together. These calculated physical totals exclude analog channels and remote I/O. Verify the complete module power budget before adding communication hardware.

Installation and Typical Applications

The controller requires 24 V DC nominal, with a permissible range of 20.4–28.8 V DC. Size the supply for the CPU, connected modules, sensors and load circuits using their respective power requirements. The enclosure rating is IP20, and installation requires a suitable control cabinet. The CPU measures 130 × 100 × 75 mm and supports DIN-rail or direct panel mounting. Allow additional space for wiring, ventilation and expansion modules. Technically suitable applications include machine sequencing, conveyor sensor monitoring, production counting, analog transmitter monitoring and pulse-command interfaces to compatible drives. Outputs must operate within their electrical ratings; motors and other substantial loads require suitable external switching or drive equipment.

Exact Variant and Documentation

Use documentation for the exact DC/DC/DC article when checking replacement wiring and compatibility. Relay-output variants and S7-1200 G2 products must not be treated as interchangeable. Verify the installed firmware, terminal assignments and optional module articles before commissioning. Standard PLC logic does not establish a safety-rated control function. The specified 12 Months warranty is the requested seller policy, not a verification of Siemens warranty terms.

Official Manufacturer Links

Official Manufacturer Product Page: https://mall.industry.siemens.com/mall/en/ua/Catalog/Product/6ES7215-1AG40-0XB0

Official Manufacturer Datasheet / Technical Documentation: https://support.industry.siemens.com/teddatasheet/?caller=SIOS&format=pdf&language=en&mlfbs=6ES7215-1AG40-0XB0

Siemens SIMATIC S7-1200 CPU’s

• Siemens SIMATIC S7-1200 CPU